Drill Bushing Search
Click on following link Drill Chart for decimal sizing.
Bushing Search - Inch
- 1 Input letter of bushing style type (P = Press Fit) and a dash...P-
- 2 Input bushing O.D. in 64th's of an inch (20=5/16") and a dash...P-20-
- 3 Input bushing length in 16th's of an inch (8=1/2") and a dash... P-20-8-
- 4 Input bushing I.D. in 10,000th's of an inch (.1250=1/8")... P-20-8-.1250
Bushing Search - Metric
- 1 Input letter of bushing style type (PM = Press Fit) and a dash...PM-
- 2 Input bushing O.D. in mm's (8) and a dash...PM-8-
- 3 Input bushing length in mm's (12) and a dash... PM-8-12-
- 4 Input bushing I.D. in two decimal mm's (4.50)... PM-18-20-4.50
Bushing Type: DG Diamond Groove
| From #55 to 1/4" | +.0001/+.0004 | 1 to 3mm | +.002/+.008mm |
| Over 1/4 to 3/4" | +.0001/+.0005 | Over 3 to 6mm | +.004/+012mm |
| Over 3/4 to 1-1/2 | +.0002/+.0006 | Over 6 to 10mm | +.005/+.014mm |
| Over 10 to 18mm | +.006/+.017mm | ||
| Over 18 to 19mm | +.007/+.020mm |
DG type bushings are used for cast-in-place or potted installation. The diamond knurled exterior provides superior holding strength against rotational and axial forces. Since the bushing's OD is not ground, the ID must be accurately located during the casting or potting process. Standard sizing and ANSI part numbers for DG and DGM (metric) type bushings are listed in the tables below.
Ordering Example: DG-40-8-.3125
| ID Range | Outside Diameter | Length | ANSI Part Number |
|---|---|---|---|
| .0520-.0995 #55-#39 1.35-2.50mm |
13/64 .233-.213 |
1/4 | DG-13-4 |
| 5/16 | DG-13-5 | ||
| 3/8 | DG-13-6 | ||
| 1/2 | DG-13-8 | ||
| .0980-.1406 #40-9/64 2.50-3.50mm |
1/4 .275-.260 |
1/4 | DG-16-4 |
| 5/16 | DG-16-5 | ||
| 3/8 | DG-16-6 | ||
| 1/2 | DG-16-8 | ||
| 3/4 | DG-16-12 | ||
| .1250-.1935 1/8-#10 3.20-4.90mm |
5/16 .337-.322 |
1/4 | DG-20-4 |
| 5/16 | DG-20-5 | ||
| 3/8 | DG-20-6 | ||
| 1/2 | DG-20-8 | ||
| 3/4 | DG-20-12 | ||
| 1 | DG-20-16 | ||
| .1562-.2570 5/32-F 4.00-6.50mm |
13/32 .431-.416 |
1/4 | DG-26-4 |
| 5/16 | DG-26-5 | ||
| 3/8 | DG-26-6 | ||
| 1/2 | DG-26-8 | ||
| 3/4 | DG-26-12 | ||
| 1 | DG-26-16 | ||
| .1562-.3160 5/32-O 4.00-8.00mm |
1/2 .525-.510 |
5/16 | DG-32-5 |
| 3/8 | DG-32-6 | ||
| 1/2 | DG-32-8 | ||
| 3/4 | DG-32-12 | ||
| 1 | DG-32-16 | ||
| .3125-.4375 5/16-7/16 7.90-11.00mm |
5/8 .650-.635 |
3/8 | DG-40-6 |
| 1/2 | DG-40-8 | ||
| 3/4 | DG-40-12 | ||
| 1 | DG-40-16 | ||
| 1-3/8 | DG-40-22 | ||
| .3125-.5312 5/16-17/32 8.00-13.00mm |
3/4 .775-.760 |
3/8 | DG-48-6 |
| 1/2 | DG-48-8 | ||
| 3/4 | DG-48-12 | ||
| 1 | DG-48-16 | ||
| 1-3/8 | DG-48-22 | ||
| .5000-.6562 1/2-21/32 13.00-16.50mm |
7/8 .900-.885 |
3/8 | DG-56-6 |
| 1/2 | DG-56-8 | ||
| 3/4 | DG-56-12 | ||
| 1 | DG-56-16 | ||
| 1-3/8 | DG-56-22 | ||
| .5000-.7656 1/2-49/64 13.00-19.00mm |
1 1.035-1.010 |
1/2 | DG-64-8 |
| 3/4 | DG-64-12 | ||
| 1 | DG-64-16 | ||
| 1-3/8 | DG-64-22 | ||
| 1-1/2 | DG-64-24 |
| ID Range | Outside Diameter | Length | ANSI Part Number |
|---|---|---|---|
| 1.00 - 1.80mm | 5mm 5.50 - 5.25mm |
6mm | DGM-5-6 |
| 9mm | DGM-5-9 | ||
1.81 - 2.60mm |
6mm | DGM-5-6 | |
| 9mm | DGM-5-9 | ||
| 2.61 - 3.30mm |
6mm 6.65 - 6.25mm |
8mm | DGM-6-8 |
| 12mm | DGM-6-12 | ||
| 16mm | DGM-6-16 | ||
| 3.31 - 4.00mm |
7mm 7.65 - 7.25mm |
8mm | DGM-7-8 |
| 12mm | DGM-7-12 | ||
| 16mm | DGM-7-16 | ||
| 4.01 - 5.00mm |
8mm 8.65 - 8.25mm |
8mm | DGM-8-8 |
| 12mm | DGM-8-12 | ||
| 16mm | DGM-8-16 | ||
| 5.01 - 6.00mm |
10mm 10.65 - 10.25mm |
10mm | DGM-10-10 |
| 16mm | DGM-10-16 | ||
| 20mm | DGM-10-20 | ||
| 6.01 - 8.00mm |
12mm 12.65 - 12.25mm |
10mm | DGM-12-10 |
| 16mm | DGM-12-16 | ||
| 20mm | DGM-12-20 | ||
| 8.01 - 10.00mm |
15mm 15.65 - 15.25mm |
12mm | DGM-15-12 |
| 20mm | DGM-15-20 | ||
| 25mm | DGM-15-25 | ||
| 10.01 - 12.00mm |
18mm 18.65 - 18.25mm |
12mm | DGM-18-12 |
| 20mm | DGM-18-20 | ||
| 25mm | DGM-18-25 | ||
| 12.01 - 15.00mm |
22mm 22.65 - 22.25mm |
16mm | DGM-22-16 |
| 28mm | DGM-22-28 | ||
| 36mm | DGM-22-36 | ||
| 15.01 - 18.00mm |
26mm 26.90 - 26.25mm |
16mm | DGM-26-16 |
| 28mm | DGM-26-28 | ||
| 36mm | DGM-26-36 |
